Case-IH MX 80 C or New Holland 5635 (A)?
Which should you choose?
On performance, every comparable figure that differs favours the Case-IH MX 80 C: hydraulic flow and maximum permissible mass.
- The Case-IH MX 80 C suits loader and hydraulic implement work better on this data: 115% (51.1 L/min / 13.5 gpm) more hydraulic flow.
- The Case-IH MX 80 C suits road haulage better on this data: 45% (2,415 kg / 5,324 lb) more maximum permissible mass.
Generated by rule set compare@4 from the figures on the side-by-side table, allowed by route “the same stated configuration”. Measured figures are compared only with measured, claimed only with claimed, at the same test condition; differences within each figure’s tolerance are not called.
What decides it, question by question?
| Question | MX 80 C | 5635 (A) | Call |
|---|---|---|---|
| Which puts more power through the PTO shaft? | 50.0 kW (67.1 hp)Traktorenlexikon, “Case-IH MX80C” | 49.9 kW (66.9 hp)Traktorenlexikon, “New Holland 5635” | EvenEven on power at the PTO shaft (both power at the PTO, claimed): the difference is under the 10% threshold for claimed figures, too small to call. |
| Which turns a litre of fuel into more work at the shaft? | — | — | No figureNo call on fuel efficiency at the shaft: no figure on record for the MX 80 C and the 5635 (A). |
| Which pulls harder at the drawbar? | — | — | No figureNo call on drawbar power: no figure on record for the MX 80 C and the 5635 (A). |
| Which pumps more oil for implements? | 95.6 L/min (25.3 gpm)Traktorenlexikon, “Case-IH MX80C” | 44.5 L/min (11.8 gpm)Traktorenlexikon, “New Holland 5635” | AheadThe Case-IH MX 80 C has 115% more hydraulic flow (51.1 L/min / 13.5 gpm) than the New Holland 5635 (A) (both pump flow, as stated by the source). |
| Which lifts more on the three-point hitch? | — | 4,200 kg (9,259 lb)Traktorenlexikon, “New Holland 5635” | No figureNo call on three-point lift: no figure on record for the MX 80 C. |
| Which is heavier, for traction? | 4,800 kg (10,582 lb)Traktorenlexikon, “Case-IH MX80C” | 4,190 kg (9,237 lb)Traktorenlexikon, “New Holland 5635” | Ahead (a fact, not an advantage)The Case-IH MX 80 C is 15% heavier (610 kg / 1,345 lb) than the New Holland 5635 (A) (both unladen weight, as stated by the source). |
| Which may carry more ballast and load? | 7,815 kg (17,229 lb)Traktorenlexikon, “Case-IH MX80C” | 5,400 kg (11,905 lb)Traktorenlexikon, “New Holland 5635” | AheadThe Case-IH MX 80 C has 45% higher maximum permissible mass (2,415 kg / 5,324 lb) than the New Holland 5635 (A) (both maximum permissible mass, as stated by the source). |
| Which has the wider choice of gears? | 16 to 32Traktorenlexikon, “Case-IH MX80C” | 12 to 24Traktorenlexikon, “New Holland 5635” | EvenEven on forward gears (both forward gears, as stated by the source): the figures vary by configuration and the ranges overlap. |
| Which offers a creeper range? | — | — | No figureNo call on a creeper range: not stated for the MX 80 C and the 5635 (A). |
| Which is faster on the road? | 30 km/h (18.6 mph) to 40 km/h (24.9 mph)Traktorenlexikon, “Case-IH MX80C” | 30 km/h (18.6 mph) to 40 km/h (24.9 mph)Traktorenlexikon, “New Holland 5635” | EvenEven on top speed (both top speed forward, as stated by the source): the figures vary by configuration and the ranges overlap. |
| Which offers more PTO speeds? | 540/1000 rpmTraktorenlexikon, “Case-IH MX80C” | 540/540E/1000 rpmTraktorenlexikon, “New Holland 5635” | EvenEven on PTO speeds: the same speeds (540, 1000 rpm). |
| Which PTO runs independently of the ground drive? | independentTraktorenlexikon, “Case-IH MX80C” | independentTraktorenlexikon, “New Holland 5635” | EvenEven on PTO independence: every PTO is independent. |
| Which drives on both axles? | 4WDTraktorenlexikon, “Case-IH MX80C”; OECD test report 1930, 2000 | 2WD / 4WDTraktorenlexikon, “New Holland 5635” | EvenEven on drive: every machine is available with four-wheel drive. |
| Which is newer, and what about parts? | 1998–2000 | 1996–1998 | EvenSame era: production began within 5 years of each other. We hold no parts-availability data, so there is no call on parts. |
What does this mean in plain words?
- The Case-IH MX 80 C has 115% more hydraulic flow (51.1 L/min / 13.5 gpm) than the New Holland 5635 (A) (both pump flow, as stated by the source).
- The Case-IH MX 80 C is 15% heavier (610 kg / 1,345 lb) than the New Holland 5635 (A) (both unladen weight, as stated by the source).
- The Case-IH MX 80 C has 45% higher maximum permissible mass (2,415 kg / 5,324 lb) than the New Holland 5635 (A) (both maximum permissible mass, as stated by the source).
- Even on power at the PTO shaft (both power at the PTO, claimed): the difference is under the 10% threshold for claimed figures, too small to call.
- Even on forward gears (both forward gears, as stated by the source): the figures vary by configuration and the ranges overlap.
- Even on top speed (both top speed forward, as stated by the source): the figures vary by configuration and the ranges overlap.
- Even on PTO speeds: the same speeds (540, 1000 rpm).
- Even on PTO independence: every PTO is independent.
- Even on drive: every machine is available with four-wheel drive.
- Same era: production began within 5 years of each other. We hold no parts-availability data, so there is no call on parts.
- No figure on record for every machine, so no call on: fuel efficiency at the shaft, drawbar power, three-point lift and a creeper range.
← Every figure for both machines, side by side, with sources