Case-IH CX 100 or Landini 11800 (DT)?
Which should you choose?
The figures split: the Case-IH CX 100 is ahead on hydraulic flow; the Landini 11800 (DT) is ahead on maximum permissible mass.
- The Case-IH CX 100 suits loader and hydraulic implement work better on this data: 19% (9.6 L/min / 2.5 gpm) more hydraulic flow.
- The Landini 11800 (DT) suits road haulage better on this data: 17% (1,000 kg / 2,205 lb) more maximum permissible mass.
Generated by rule set compare@4 from the figures on the side-by-side table, allowed by route “the same stated configuration”. Measured figures are compared only with measured, claimed only with claimed, at the same test condition; differences within each figure’s tolerance are not called.
What decides it, question by question?
| Question | CX 100 | 11800 (DT) | Call |
|---|---|---|---|
| Which puts more power through the PTO shaft? | 65.0 kW (87.2 hp)Traktorenlexikon, “Case-IH CX100” | 64.8 kW (86.9 hp)Traktorenlexikon, “Landini 11800 DT” | EvenEven on power at the PTO shaft (both power at the PTO, claimed): the difference is under the 10% threshold for claimed figures, too small to call. |
| Which turns a litre of fuel into more work at the shaft? | — | — | No figureNo call on fuel efficiency at the shaft: no figure on record for the CX 100 and the 11800 (DT). |
| Which pulls harder at the drawbar? | — | — | No figureNo call on drawbar power: no figure on record for the CX 100 and the 11800 (DT). |
| Which pumps more oil for implements? | 60.8 L/min (16.1 gpm)Traktorenlexikon, “Case-IH CX100” | 51.2 L/min (13.5 gpm)Traktorenlexikon, “Landini 11800 DT” | AheadThe Case-IH CX 100 has 19% more hydraulic flow (9.6 L/min / 2.5 gpm) than the Landini 11800 (DT) (both pump flow, as stated by the source). |
| Which lifts more on the three-point hitch? | 3,835 kg (8,455 lb)Traktorenlexikon, “Case-IH CX100” | 4,497 kg (9,914 lb)Traktorenlexikon, “Landini 11800 DT” | Not comparableNot comparable on three-point lift: the CX 100: lift through the full range at the hitch ends, as stated by the source (Traktorenlexikon, “Case-IH CX100”); the 11800 (DT): lift at the hitch ends, as stated by the source (Traktorenlexikon, “Landini 11800 DT”) — not the same quantity, basis and condition. |
| Which is heavier, for traction? | 4,235 kg (9,337 lb)Traktorenlexikon, “Case-IH CX100” | 4,390 kg (9,678 lb)Traktorenlexikon, “Landini 11800 DT” | EvenEven on weight (both unladen weight, as stated by the source): the difference is under the 10% threshold, too small to call. |
| Which may carry more ballast and load? | 6,000 kg (13,228 lb)Traktorenlexikon, “Case-IH CX100” | 7,000 kg (15,432 lb)Traktorenlexikon, “Landini 11800 DT” | AheadThe Landini 11800 (DT) has 17% higher maximum permissible mass (1,000 kg / 2,205 lb) than the Case-IH CX 100 (both maximum permissible mass, as stated by the source). |
| Which has the wider choice of gears? | 8 to 24Traktorenlexikon, “Case-IH CX100” | 32Traktorenlexikon, “Landini 11800 DT” | Sources disagreeNo call on forward gears: sources disagree on the figure for the CX 100. |
| Which offers a creeper range? | — | — | No figureNo call on a creeper range: not stated for the CX 100 and the 11800 (DT). |
| Which is faster on the road? | 30 km/h (18.6 mph) to 40 km/h (24.9 mph)Traktorenlexikon, “Case-IH CX100” | 30 km/h (18.6 mph) to 40 km/h (24.9 mph)Traktorenlexikon, “Landini 11800 DT” | EvenEven on top speed (both top speed forward, as stated by the source): the figures vary by configuration and the ranges overlap. |
| Which offers more PTO speeds? | 540/1000 rpmTraktorenlexikon, “Case-IH CX100” | 540/1000 rpmTraktorenlexikon, “Landini 11800 DT” | EvenEven on PTO speeds: the same speeds (540, 1000 rpm). |
| Which PTO runs independently of the ground drive? | independentTraktorenlexikon, “Case-IH CX100” | — | No figureNo call on PTO independence: not stated for the 11800 (DT). |
| Which drives on both axles? | 4WDTraktorenlexikon, “Case-IH CX100”; OECD test report 1899, 2000 | Two-wheel or four-wheel driveTraktorenlexikon, “Landini 11800 DT” | EvenEven on drive: every machine is available with four-wheel drive. |
| Which is newer, and what about parts? | 1998–2000 | 1987–2000 | Ahead (a fact, not an advantage)The Case-IH CX 100 is newer: production began 11 years later. We hold no parts-availability data, so there is no call on parts. |
What does this mean in plain words?
- The Case-IH CX 100 has 19% more hydraulic flow (9.6 L/min / 2.5 gpm) than the Landini 11800 (DT) (both pump flow, as stated by the source).
- The Landini 11800 (DT) has 17% higher maximum permissible mass (1,000 kg / 2,205 lb) than the Case-IH CX 100 (both maximum permissible mass, as stated by the source).
- The Case-IH CX 100 is newer: production began 11 years later. We hold no parts-availability data, so there is no call on parts.
- Even on power at the PTO shaft (both power at the PTO, claimed): the difference is under the 10% threshold for claimed figures, too small to call.
- Even on weight (both unladen weight, as stated by the source): the difference is under the 10% threshold, too small to call.
- Even on top speed (both top speed forward, as stated by the source): the figures vary by configuration and the ranges overlap.
- Even on PTO speeds: the same speeds (540, 1000 rpm).
- Even on drive: every machine is available with four-wheel drive.
- Not comparable on three-point lift: the CX 100: lift through the full range at the hitch ends, as stated by the source (Traktorenlexikon, “Case-IH CX100”); the 11800 (DT): lift at the hitch ends, as stated by the source (Traktorenlexikon, “Landini 11800 DT”) — not the same quantity, basis and condition.
- No call on forward gears: sources disagree on the figure for the CX 100.
- No figure on record for every machine, so no call on: fuel efficiency at the shaft, drawbar power, a creeper range and PTO independence.
← Every figure for both machines, side by side, with sources