Case-IH 9240 vs John Deere 8210 T
11 material differences · fewer than 12
Which should you choose?
We will not advise between these two machines, because the drive differs (4WD; Tracks); they were not built in overlapping years (1990–1994; 2000–2002); the 8210 T is on tracks, not an alternative to an ordinary tractor. The figures below are side by side so you can judge them yourself; each says whether it was measured, claimed or declared by its source.
Field by field
11 material differences · 4 fields identical or within 5%, which is not counted as material
| Field | 9240 | 8210 T | Gap |
|---|---|---|---|
| Engine | |||
| Engine power, claimed claimed | 231.7 hp | 212.1 hp | +9% 9240 |
| Engine declared | CUMMINS 6 TA-830 | John Deere-PowerTech 6.081 HRW-14 | differs |
| Displacement declared | 8.27 L | 8.13 L | — |
| Maximum torque declared | 603 lb·ft · 818 N·m | 662 lb·ft · 898 N·m | +10% 8210 T |
| Transmission | |||
| Top speed declared | 18.6 mph · 30 km/h | 18.6 mph · 30 km/h | — |
| Clutch declared | F.T.K. multi-plate clutch running in oil bath | Pedal-operated, hydraulic-wet John Deere multi-plate clutch | differs |
| Hydraulics & hitch | |||
| Hydraulic centre declared | — | Closed centre | — |
| Hydraulic control declared | — | Load sensing | — |
| Pump flow declared | 29.1 gpm · 110.2 L/min | 34.7 gpm · 131.4 L/min | +19% 8210 T |
| Pressure declared | 3,002 psi · 207 bar | 3,379 psi · 233 bar | +13% 8210 T |
| Three-point lift at ends declared | 14,703 lb · 6,669 kg | — | — |
| Rear PTO speeds declared | 1000 rpm | 1000 rpm | — |
| Weight & dimensions | |||
| Unladen weight declared | 28,215 lb · 12,798 kg | 25,399 lb · 11,521 kg | +11% 9240 |
| Maximum permissible mass declared | — | 31,500 lb · 14,288 kg | — |
| Wheelbase declared | 124.0 in · 3,150 mm | 89.0 in · 2,260 mm | +39% 9240 |
| Length declared | 256.6 in · 6,517 mm | 216.0 in · 5,487 mm | +19% 9240 |
| Width declared | 104.8 in · 2,661 mm | 134.0 in · 3,404 mm | +28% 8210 T |
| Height declared | 125.9 in · 3,198 mm | 123.4 in · 3,135 mm | — |
| Ground clearance declared | 13.4 in · 340 mm | 14.2 in · 360 mm | +6% 8210 T |
| Fuel tank declared | 799.9 qt · 757.0 L | 519.9 qt · 492.0 L | +54% 9240 |
Case-IH 9240 sources
Source
- Source: Traktorenlexikon, “Case-IH 9240”
- Source: Traktorenlexikon, “Case-IH 7230 PRO/8930”
John Deere 8210 T sources
Source
- Source: Traktorenlexikon, “John Deere 8210T”
- Source: OECD test report 1934, 2000