Case-IH 7230 Magnum vs John Deere 8200 T
13 material differences
Which should you choose?
We will not advise between these two machines, because their unladen weight differs by more than 25% (44%); the drive differs (4WD; Tracks); the 8200 T is on tracks, not an alternative to an ordinary tractor. The figures below are side by side so you can judge them yourself; each says whether it was measured, claimed or declared by its source.
Field by field
13 material differences · 3 fields identical or within 5%, which is not counted as material
| Field | 7230 Magnum | 8200 T | Gap |
|---|---|---|---|
| Engine | |||
| Engine power, claimed claimed | 204.1 hp | 207.3 hp | — |
| Engine declared | CUMMINS 6 T-830 | John Deere-PowerTech 6.081 HRW-03 | differs |
| Displacement declared | 8.27 L | 8.13 L | — |
| Maximum torque declared | 586 lb·ft · 795 N·m | 659 lb·ft · 893 N·m | +12% 8200 T |
| Transmission | |||
| Top speed declared | 18.6–24.9 mph · 30–40 km/h | 18.6 mph · 30 km/h | differs |
| Clutch declared | Case-IH multi-plate clutch running in oil bath | Pedal-operated, hydraulic-wet John Deere multi-disc clutch | differs |
| Hydraulics & hitch | |||
| Hydraulic centre declared | — | Closed centre | — |
| Hydraulic control declared | — | Load sensing | — |
| Pump flow declared | 29.3 gpm · 110.9 L/min | 31.1 gpm · 117.7 L/min | +6% 8200 T |
| Pressure declared | 2,451 psi · 169 bar | 3,379 psi · 233 bar | +38% 8200 T |
| Three-point lift at ends declared | — | 15,763 lb · 7,150 kg | — |
| Rear PTO speeds declared | 540/1000 rpm | 1000 rpm | differs |
| Weight & dimensions | |||
| Unladen weight declared | 17,789 lb · 8,069 kg | 25,589 lb · 11,607 kg | +44% 8200 T |
| Maximum permissible mass declared | 25,519 lb · 11,575 kg | — | — |
| Wheelbase declared | 118.3 in · 3,006 mm | 89.0 in · 2,260 mm | +33% 7230 Magnum |
| Length declared | 200.1 in · 5,083 mm | 216.0 in · 5,487 mm | +8% 8200 T |
| Width declared | 120.0 in · 3,048 mm | 102.0 in · 2,591 mm | +18% 7230 Magnum |
| Height declared | 119.8 in · 3,042 mm | 123.4 in · 3,135 mm | — |
| Ground clearance declared | 17.9 in · 454 mm | 14.2 in · 360 mm | +26% 7230 Magnum |
| Fuel tank declared | 273.7–379.4 qt · 259.0–359.0 L | 519.9 qt · 492.0 L | differs |
Case-IH 7230 Magnum sources
Source
- Source: Traktorenlexikon, “Case-IH 7230”
- Source: Traktorenlexikon, “Case-IH 7110”
John Deere 8200 T sources
Source
- Source: Traktorenlexikon, “John Deere 8200T”
- Source: OECD test report 1781, 1998