BOLINDER-MUNKTELL BM-24/BM-25 or Hermann Lanz D 30?
Which should you choose?
The data can’t decide this. Power at the PTO shaft cannot be compared: the BM-24/BM-25 has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft; the D 30 has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft.
- The Hermann Lanz D 30 suits loader and hydraulic implement work better on this data: 43% (10.2 L/min / 2.7 gpm) more hydraulic flow.
Generated by rule set compare@4 from the figures on the side-by-side table, allowed by route “the same stated configuration”. Measured figures are compared only with measured, claimed only with claimed, at the same test condition; differences within each figure’s tolerance are not called.
What decides it, question by question?
| Question | BM-24/BM-25 | D 30 | Call |
|---|---|---|---|
| Which puts more power through the PTO shaft? | 20.6 kW (27.6 hp)Traktorenlexikon, “Bolinder-Munktell BM 24/25” | 20.5 kW (27.5 hp)Traktorenlexikon, “HELA D30” | Not comparableNot comparable on power at the PTO shaft: the BM-24/BM-25 has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft; the D 30 has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft. |
| Which turns a litre of fuel into more work at the shaft? | — | — | No figureNo call on fuel efficiency at the shaft: no figure on record for the BM-24/BM-25 and the D 30. |
| Which pulls harder at the drawbar? | — | — | No figureNo call on drawbar power: no figure on record for the BM-24/BM-25 and the D 30. |
| Which pumps more oil for implements? | 23.8 L/min (6.3 gpm)Traktorenlexikon, “Bolinder-Munktell BM 24/25” | 34.0 L/min (9.0 gpm)Traktorenlexikon, “HELA D30” | AheadThe Hermann Lanz D 30 has 43% more hydraulic flow (10.2 L/min / 2.7 gpm) than the BOLINDER-MUNKTELL BM-24/BM-25 (both pump flow, as stated by the source). |
| Which lifts more on the three-point hitch? | 580 kg (1,279 lb)Traktorenlexikon, “Bolinder-Munktell BM 24/25” | — | No figureNo call on three-point lift: no figure on record for the D 30. |
| Which is heavier, for traction? | 1,569 kg (3,459 lb) to 1,589 kg (3,503 lb)Traktorenlexikon, “Bolinder-Munktell BM 24/25” | 1,665 kg (3,671 lb)Traktorenlexikon, “HELA D30” | EvenEven on weight (both unladen weight, as stated by the source): the difference is under the 10% threshold, too small to call. |
| Which may carry more ballast and load? | — | — | No figureNo call on maximum permissible mass: no figure on record for the BM-24/BM-25 and the D 30. |
| Which has the wider choice of gears? | 5Traktorenlexikon, “Bolinder-Munktell BM 24/25” | 6Traktorenlexikon, “HELA D30” | EvenEven on forward gears (both forward gears, as stated by the source): the difference is under the 25% threshold, too small to call. |
| Which offers a creeper range? | — | YesTraktorenlexikon, “HELA D30” | No figureNo call on a creeper range: not stated for the BM-24/BM-25. |
| Which is faster on the road? | 20 km/h (12.4 mph)Traktorenlexikon, “Bolinder-Munktell BM 24/25” | 19.8 km/h (12.3 mph)Traktorenlexikon, “HELA D30” | EvenEven on top speed (both top speed forward, as stated by the source): the difference is under the 10% threshold, too small to call. |
| Which offers more PTO speeds? | 540 rpmTraktorenlexikon, “Bolinder-Munktell BM 24/25” | 572 rpmTraktorenlexikon, “HELA D30” | No figureNo call on PTO speeds: no standard PTO speed stated for the D 30. |
| Which PTO runs independently of the ground drive? | — | dependent (stops with the clutch)Traktorenlexikon, “HELA D30” | No figureNo call on PTO independence: not stated for the BM-24/BM-25. |
| Which drives on both axles? | 2WDTraktorenlexikon, “Bolinder-Munktell BM 24/25” | 2WDTraktorenlexikon, “HELA D30” | EvenEven on drive: all two-wheel drive. |
| Which is newer, and what about parts? | 1952–1959 | 1956–1960 | EvenSame era: production began within 5 years of each other. We hold no parts-availability data, so there is no call on parts. |
What does this mean in plain words?
- The Hermann Lanz D 30 has 43% more hydraulic flow (10.2 L/min / 2.7 gpm) than the BOLINDER-MUNKTELL BM-24/BM-25 (both pump flow, as stated by the source).
- Even on weight (both unladen weight, as stated by the source): the difference is under the 10% threshold, too small to call.
- Even on forward gears (both forward gears, as stated by the source): the difference is under the 25% threshold, too small to call.
- Even on top speed (both top speed forward, as stated by the source): the difference is under the 10% threshold, too small to call.
- Even on drive: all two-wheel drive.
- Same era: production began within 5 years of each other. We hold no parts-availability data, so there is no call on parts.
- Not comparable on power at the PTO shaft: the BM-24/BM-25 has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft; the D 30 has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft.
- No figure on record for every machine, so no call on: fuel efficiency at the shaft, drawbar power, three-point lift, maximum permissible mass, a creeper range, PTO speeds and PTO independence.
← Every figure for both machines, side by side, with sources