10 material differences · fewer than 12
Tractor oneALLIS-CHALMERS One-Sixty / 1601970–1975No measured PTO figureTractor twoSOMECA SOM-431 V/E1964–1965No measured PTO figure
Which should you choose?
Read our verdict on the One-Sixty / 160 and the SOM-431 V/E → It is generated from the rows below by a fixed, versioned rule set, and names the figure behind every call.
Field by field
10 material differences · 3 fields identical or within 5%, which is not counted as material
| Field | One-Sixty / 160 | SOM-431 V/E | Gap |
|---|---|---|---|
| Engine | |||
| Engine power, claimed claimed | 40.5 hp | 40.5 hp | — |
| Engine declared | Perkins AD 3.152 | O.M.-FIAT 615.000 | differs |
| Displacement declared | 2.50 L | 2.27 L | +10% One-Sixty / 160 |
| Maximum torque declared | 114 lb·ft · 155 N·m | 101 lb·ft · 137 N·m | +13% One-Sixty / 160 |
| Transmission | |||
| Top speed declared | 15.5 mph · 25 km/h | 10.6 mph · 17 km/h | +47% One-Sixty / 160 |
| Clutch declared | — | Pedal-operated two-stage dry double clutch | — |
| Hydraulics & hitch | |||
| Hydraulic centre declared | Open centre | — | — |
| Pump flow declared | 6.7 gpm · 25.4 L/min | 4.4 gpm · 16.5 L/min | +54% One-Sixty / 160 |
| Pressure declared | — | 2,843 psi · 196 bar | — |
| Rear PTO speeds declared | 540 rpm | 540 rpm | — |
| Weight & dimensions | |||
| Unladen weight declared | 5,721 lb · 2,595 kg | 3,197 lb · 1,450 kg | +79% One-Sixty / 160 |
| Wheelbase declared | 76.0 in · 1,930 mm | 71.7 in · 1,820 mm | +6% One-Sixty / 160 |
| Length declared | 138.0 in · 3,505 mm | 112.2 in · 2,850 mm | +23% One-Sixty / 160 |
| Width declared | 64.2 in · 1,630 mm | 38.6 in · 980 mm | +66% One-Sixty / 160 |
| Ground clearance declared | 19.0 in · 483 mm | 13.8 in · 350 mm | +38% One-Sixty / 160 |
| Turning radius, braked declared | 8.3 ft · 2.52 m | — | — |
| Fuel tank declared | 53.9 qt · 51.0 L | 51.8 qt · 49.0 L | — |
Height is not in this table. It is not one measurement: the sources measure it to different points — over the cab on some machines, over the steering wheel or the exhaust on others — and the same tractor measured two ways can differ by most of a metre. It appears here only when both machines' figures carry the point they were measured to and it is the same point, which is not the case for these two. Each machine's own page prints its height as its source gives it.
ALLIS-CHALMERS One-Sixty / 160 sources
- Source: Traktorenlexikon, “Allis-Chalmers 160”
- Source: Traktorenlexikon, “Massey Ferguson MF 148”
SOMECA SOM-431 V/E sources
- Source: Traktorenlexikon, “Someca SOM 431”
- Source: Traktorenlexikon, “Someca SOM 35”