9 material differences · fewer than 12
Tractor oneALLIS-CHALMERS One-Sixty / 1601970–1975No measured PTO figureTractor twoJohn Deere 9301974–1977No measured PTO figure
Which should you choose?
Read our verdict on the One-Sixty / 160 and the 930 → It is generated from the rows below by a fixed, versioned rule set, and names the figure behind every call.
Field by field
9 material differences · 5 fields identical or within 5%, which is not counted as material
| Field | One-Sixty / 160 | 930 | Gap |
|---|---|---|---|
| Engine | |||
| Engine power, claimed claimed | 40.5 hp | 40.5 hp | — |
| Engine declared | Perkins AD 3.152 | John Deere 3.164 DL 15 | differs |
| Displacement declared | 2.50 L | 2.70 L | +8% 930 |
| Maximum torque declared | 114 lb·ft · 155 N·m | 107 lb·ft · 145 N·m | +7% One-Sixty / 160 |
| Transmission | |||
| Top speed declared | 15.5 mph · 25 km/h | 16.8–18.6 mph · 27–30 km/h | differs |
| Clutch declared | — | Pedal operated, two-stage dry Fichtel & Sachs double clutch | — |
| Hydraulics & hitch | |||
| Hydraulic centre declared | Open centre | Open centre | — |
| Pump flow declared | 6.7 gpm · 25.4 L/min | 6.7 gpm · 25.4 L/min | — |
| Pressure declared | — | 3,481–4,496 psi · 240–310 bar | — |
| Rear PTO speeds declared | 540 rpm | — | — |
| Weight & dimensions | |||
| Unladen weight declared | 5,721 lb · 2,595 kg | 4,817 lb · 2,185 kg | +19% One-Sixty / 160 |
| Maximum permissible mass declared | — | 7,055 lb · 3,200 kg | — |
| Wheelbase declared | 76.0 in · 1,930 mm | 74.4 in · 1,890 mm | — |
| Length declared | 138.0 in · 3,505 mm | 136.2 in · 3,460 mm | — |
| Width declared | 64.2 in · 1,630 mm | 66.5–86.2 in · 1,690–2,190 mm | differs |
| Ground clearance declared | 19.0 in · 483 mm | 12.8 in · 325 mm | +49% One-Sixty / 160 |
| Turning radius, braked declared | 8.3 ft · 2.52 m | 9.6 ft · 2.92 m | +16% 930 |
| Fuel tank declared | 53.9 qt · 51.0 L | 66.0 qt · 62.5 L | +23% 930 |
Height is not in this table. It is not one measurement: the sources measure it to different points — over the cab on some machines, over the steering wheel or the exhaust on others — and the same tractor measured two ways can differ by most of a metre. It appears here only when both machines' figures carry the point they were measured to and it is the same point, which is not the case for these two. Each machine's own page prints its height as its source gives it.
ALLIS-CHALMERS One-Sixty / 160 sources
- Source: Traktorenlexikon, “Allis-Chalmers 160”
- Source: Traktorenlexikon, “Massey Ferguson MF 148”
John Deere 930 sources
- Source: Traktorenlexikon, “John Deere 930”