ALLIS-CHALMERS FD-3 or Leyland 154?
Which should you choose?
The data can’t decide this. Power at the PTO shaft cannot be compared: the FD-3 has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft; the 154 has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft.
- The Leyland 154 suits road haulage better on this data: 25% (5.0 km/h / 3.1 mph) more top speed.
Generated by rule set compare@4 from the figures on the side-by-side table, allowed by route “the same stated configuration”. Measured figures are compared only with measured, claimed only with claimed, at the same test condition; differences within each figure’s tolerance are not called.
What decides it, question by question?
| Question | FD-3 | 154 | Call |
|---|---|---|---|
| Which puts more power through the PTO shaft? | 18.4 kW (24.7 hp)Traktorenlexikon, “Allis-Chalmers FD 3” | 18.6 kW (24.9 hp)Traktorenlexikon, “Leyland 154” | Not comparableNot comparable on power at the PTO shaft: the FD-3 has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft; the 154 has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft. |
| Which turns a litre of fuel into more work at the shaft? | — | — | No figureNo call on fuel efficiency at the shaft: no figure on record for the FD-3 and the 154. |
| Which pulls harder at the drawbar? | — | — | No figureNo call on drawbar power: no figure on record for the FD-3 and the 154. |
| Which pumps more oil for implements? | — | 14.5 L/min (3.8 gpm)Traktorenlexikon, “Leyland 154” | No figureNo call on hydraulic flow: no figure on record for the FD-3. |
| Which lifts more on the three-point hitch? | 800 kg (1,764 lb)Traktorenlexikon, “Allis-Chalmers FD 3” | 454 kg (1,001 lb)Traktorenlexikon, “Leyland 154” | Not comparableNot comparable on three-point lift: the FD-3: lift at the hitch ends, as stated by the source (Traktorenlexikon, “Allis-Chalmers FD 3”); the 154: lift through the full range at the hitch ends, as stated by the source (Traktorenlexikon, “Leyland 154”) — not the same quantity, basis and condition. |
| Which is heavier, for traction? | 1,430 kg (3,153 lb)Traktorenlexikon, “Allis-Chalmers FD 3” | 1,007 kg (2,220 lb) to 1,032 kg (2,275 lb)Traktorenlexikon, “Leyland 154” | Ahead (a fact, not an advantage)The ALLIS-CHALMERS FD-3 is 39% heavier (398 kg / 877 lb) than the Leyland 154 (both unladen weight, as stated by the source). |
| Which may carry more ballast and load? | — | — | No figureNo call on maximum permissible mass: no figure on record for the FD-3 and the 154. |
| Which has the wider choice of gears? | 8Traktorenlexikon, “Allis-Chalmers FD 3” | 9Traktorenlexikon, “Leyland 154” | EvenEven on forward gears (both forward gears, as stated by the source): the difference is under the 25% threshold, too small to call. |
| Which offers a creeper range? | — | — | No figureNo call on a creeper range: not stated for the FD-3 and the 154. |
| Which is faster on the road? | 20 km/h (12.4 mph)Traktorenlexikon, “Allis-Chalmers FD 3” | 25 km/h (15.5 mph)Traktorenlexikon, “Leyland 154” | AheadThe Leyland 154 has 25% more top speed (5.0 km/h / 3.1 mph) than the ALLIS-CHALMERS FD-3 (both top speed forward, as stated by the source). |
| Which offers more PTO speeds? | 540/1000 rpmTraktorenlexikon, “Allis-Chalmers FD 3” | 540 rpmTraktorenlexikon, “Leyland 154” | AheadThe ALLIS-CHALMERS FD-3 offers 1000 rpm at the PTO, which the Leyland 154 does not (as stated by the sources). |
| Which PTO runs independently of the ground drive? | independentTraktorenlexikon, “Allis-Chalmers FD 3” | — | No figureNo call on PTO independence: not stated for the 154. |
| Which drives on both axles? | 2WDTraktorenlexikon, “Allis-Chalmers FD 3” | 2WDTraktorenlexikon, “Leyland 154” | EvenEven on drive: all two-wheel drive. |
| Which is newer, and what about parts? | 1962–1965 | 1969–1972 | Ahead (a fact, not an advantage)The Leyland 154 is newer: production began 7 years later. We hold no parts-availability data, so there is no call on parts. |
What does this mean in plain words?
- The ALLIS-CHALMERS FD-3 is 39% heavier (398 kg / 877 lb) than the Leyland 154 (both unladen weight, as stated by the source).
- The Leyland 154 has 25% more top speed (5.0 km/h / 3.1 mph) than the ALLIS-CHALMERS FD-3 (both top speed forward, as stated by the source).
- The ALLIS-CHALMERS FD-3 offers 1000 rpm at the PTO, which the Leyland 154 does not (as stated by the sources).
- The Leyland 154 is newer: production began 7 years later. We hold no parts-availability data, so there is no call on parts.
- Even on forward gears (both forward gears, as stated by the source): the difference is under the 25% threshold, too small to call.
- Even on drive: all two-wheel drive.
- Not comparable on power at the PTO shaft: the FD-3 has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft; the 154 has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft.
- Not comparable on three-point lift: the FD-3: lift at the hitch ends, as stated by the source (Traktorenlexikon, “Allis-Chalmers FD 3”); the 154: lift through the full range at the hitch ends, as stated by the source (Traktorenlexikon, “Leyland 154”) — not the same quantity, basis and condition.
- No figure on record for every machine, so no call on: fuel efficiency at the shaft, drawbar power, hydraulic flow, maximum permissible mass, a creeper range and PTO independence.
← Every figure for both machines, side by side, with sources