10 material differences · fewer than 12
Tractor oneALLIS-CHALMERS 220 Landhandler1969–1973No measured PTO figureTractor twoDeutz-Fahr DX 6.50 A1983–1990No measured PTO figure
Which should you choose?
Read our verdict on the 220 Landhandler and the DX 6.50 A → It is generated from the rows below by a fixed, versioned rule set, and names the figure behind every call.
Field by field
10 material differences · 3 fields identical or within 5%, which is not counted as material
| Field | 220 Landhandler | DX 6.50 A | Gap |
|---|---|---|---|
| Engine | |||
| Engine power, claimed claimed | 136.1 hp | 135.2 hp | — |
| Engine declared | ALLIS-CHALMERS D-3500 | KHD BF6L 913.101T | differs |
| Displacement declared | 6.97 L | 6.13 L | +14% 220 Landhandler |
| Maximum torque declared | — | 375 lb·ft · 508 N·m | — |
| Transmission | |||
| Top speed declared | 18.6 mph · 30 km/h | 18.6–24.9 mph · 30–40 km/h | differs |
| Hydraulics & hitch | |||
| Hydraulic centre declared | Open centre | — | — |
| Pump flow declared | 16.5 gpm · 62.5 L/min | 15.2 gpm · 57.6 L/min | +9% 220 Landhandler |
| Pressure declared | — | 3,481 psi · 240 bar | — |
| Rear PTO speeds declared | 1000 rpm | 540/1000 rpm | differs |
| Weight & dimensions | |||
| Unladen weight declared | 12,161 lb · 5,516 kg | 12,081 lb · 5,480 kg | — |
| Maximum permissible mass declared | — | 17,637 lb · 8,000 kg | — |
| Wheelbase declared | 100.0 in · 2,539 mm | 106.4 in · 2,703 mm | +6% DX 6.50 A |
| Length declared | 164.0 in · 4,166 mm | 179.5 in · 4,560 mm | +9% DX 6.50 A |
| Width declared | 96.0 in · 2,438 mm | 93.3 in · 2,370 mm | — |
| Ground clearance declared | 21.0 in · 533 mm | 22.4 in · 570 mm | +7% DX 6.50 A |
| Turning radius, braked declared | 11.3 ft · 3.45 m | 17.0 ft · 5.17 m | +50% DX 6.50 A |
| Fuel tank declared | 203.9 qt · 193.0 L | 158.5 qt · 150 L | +29% 220 Landhandler |
Height is not in this table. It is not one measurement: the sources measure it to different points — over the cab on some machines, over the steering wheel or the exhaust on others — and the same tractor measured two ways can differ by most of a metre. It appears here only when both machines' figures carry the point they were measured to and it is the same point, which is not the case for these two. Each machine's own page prints its height as its source gives it.
ALLIS-CHALMERS 220 Landhandler sources
- Source: Traktorenlexikon, “Allis-Chalmers 220”
- Source: Traktorenlexikon, “Allis-Chalmers 210”
Deutz-Fahr DX 6.50 A sources
- Source: Traktorenlexikon, “Deutz-Fahr DX 6.50”