8 material differences · fewer than 12
Tractor oneAgco DT-225 B2009–2010No measured PTO figureTractor twoJohn Deere 8410 T2000–2002No measured PTO figure
Which should you choose?
Read our verdict on the DT-225 B and the 8410 T → It is generated from the rows below by a fixed, versioned rule set, and names the figure behind every call.
Field by field
8 material differences · 6 fields identical or within 5%, which is not counted as material
| Field | DT-225 B | 8410 T | Gap |
|---|---|---|---|
| Engine | |||
| Engine power, claimed claimed | 261.4 hp | 266.5 hp | — |
| Engine declared | SISU-DIESEL 84 CTA-4V | John Deere-PowerTech 6.081 HRW-18 | differs |
| Displacement declared | 8.42 L | 8.13 L | — |
| Maximum torque declared | — | 844 lb·ft · 1,144 N·m | — |
| Transmission | |||
| Top speed declared | 24.9–31.1 mph · 40–50 km/h | 18.6 mph · 30 km/h | differs |
| Clutch declared | — | Pedal operated hydraulic wet John Deere multi-plate clutch | — |
| Hydraulics & hitch | |||
| Hydraulic centre declared | — | Closed centre | — |
| Hydraulic control declared | Load sensing | Load sensing | — |
| Pump flow declared | 27.9 gpm · 105.5 L/min | 31.4 gpm · 118.9 L/min | +13% 8410 T |
| Pressure declared | 3,336 psi · 230 bar | 2,944 psi · 203 bar | +13% DT-225 B |
| Rear PTO speeds declared | 1000 rpm | 1000 rpm | — |
| Weight & dimensions | |||
| Unladen weight declared | 25,838 lb · 11,720 kg | 26,378 lb · 11,965 kg | — |
| Maximum permissible mass declared | — | 31,500 lb · 14,288 kg | — |
| Wheelbase declared | 122.2 in · 3,105 mm | 89.0 in · 2,260 mm | +37% DT-225 B |
| Length declared | 215.7 in · 5,479 mm | 216.0 in · 5,487 mm | — |
| Width declared | 79.3 in · 2,014 mm | 134.0–150.0 in · 3,404–3,810 mm | differs |
| Ground clearance declared | 18.5 in · 470 mm | 14.2 in · 360 mm | +31% DT-225 B |
| Turning radius, braked declared | 24.3 ft · 7.40 m | — | — |
| Fuel tank declared | 623.4 qt · 590.0 L | 519.9 qt · 492.0 L | +20% DT-225 B |
Height is not in this table. It is not one measurement: the sources measure it to different points — over the cab on some machines, over the steering wheel or the exhaust on others — and the same tractor measured two ways can differ by most of a metre. It appears here only when both machines' figures carry the point they were measured to and it is the same point, which is not the case for these two. Each machine's own page prints its height as its source gives it.
Agco DT-225 B sources
- Source: Traktorenlexikon, “AGCO DT 225 B”
- Source: Traktorenlexikon, “AGCO DT 205 B”
John Deere 8410 T sources
- Source: Traktorenlexikon, “John Deere 8410T”
- Source: OECD test report 1937, 2000