11 material differences · fewer than 12
Tractor oneAGCO-ALLIS 96951994–1998No measured PTO figureTractor twoDeutz-Fahr DX 2301980–1982No measured PTO figure
Which should you choose?
We will not advise between these two machines, because they were not built in overlapping years (1994–1998; 1980–1982). The figures below are side by side so you can judge them yourself; each says whether it was measured, claimed or declared by its source.
Field by field
11 material differences · 3 fields identical or within 5%, which is not counted as material
| Field | 9695 | DX 230 | Gap |
|---|---|---|---|
| Engine | |||
| Engine power, claimed claimed | 195.3 hp | 196.3 hp | — |
| Engine declared | DETROIT-DIESEL DT-530 | KHD BF6L 413 FR | differs |
| Displacement declared | 8.71 L | 9.57 L | +10% DX 230 |
| Maximum torque declared | 654 lb·ft · 887 N·m | 553 lb·ft · 750 N·m | +18% 9695 |
| Transmission | |||
| Top speed declared | 24.9 mph · 40 km/h | 15.5–18.6 mph · 25–30 km/h | differs |
| Clutch declared | Electro-hydraulically operated wet Funk multi-plate clutch type 9400 | — | — |
| Hydraulics & hitch | |||
| Hydraulic centre declared | Closed centre | Open centre | differs |
| Pump flow declared | 20.6 gpm · 78.0 L/min | 21.4 gpm · 81 L/min | — |
| Pressure declared | 2,944 psi · 203 bar | — | — |
| Rear PTO speeds declared | 1000 rpm | 923 rpm | differs |
| Weight & dimensions | |||
| Unladen weight declared | 18,592 lb · 8,433 kg | 20,393 lb · 9,250 kg | +10% DX 230 |
| Maximum permissible mass declared | — | 26,455 lb · 12,000 kg | — |
| Wheelbase declared | 116.5 in · 2,959 mm | 118.6 in · 3,012 mm | — |
| Length declared | 200.0 in · 5,080 mm | 213.7 in · 5,427 mm | +7% DX 230 |
| Width declared | 98.0–115.0 in · 2,489–2,921 mm | 98.4 in · 2,500 mm | differs |
| Ground clearance declared | 22.5 in · 572 mm | 20.7 in · 525 mm | +9% 9695 |
| Turning radius, braked declared | 14.8 ft · 4.50 m | — | — |
| Fuel tank declared | 387.8 qt · 367.0 L | 422.7 qt · 400 L | +9% DX 230 |
Height is not in this table. It is not one measurement: the sources measure it to different points — over the cab on some machines, over the steering wheel or the exhaust on others — and the same tractor measured two ways can differ by most of a metre. It appears here only when both machines' figures carry the point they were measured to and it is the same point, which is not the case for these two. Each machine's own page prints its height as its source gives it.
AGCO-ALLIS 9695 sources
- Source: Traktorenlexikon, “AGCO-Allis 9695”
- Source: Traktorenlexikon, “AGCO-Allis 9675”
Deutz-Fahr DX 230 sources
- Source: Traktorenlexikon, “Deutz-Fahr DX 230”