8 material differences · fewer than 12
Tractor oneAGCO-ALLIS 91901991–1992No measured PTO figureTractor twoSchlüter Profi Trac 2000 VL1976No measured PTO figure
Which should you choose?
We will not advise between these two machines, because their unladen weight differs by more than 25% (26%); the drive differs (Two-wheel or four-wheel drive; 4WD); they were not built in overlapping years (1991–1992; 1976–1976). The figures below are side by side so you can judge them yourself; each says whether it was measured, claimed or declared by its source.
Field by field
8 material differences · 5 fields identical or within 5%, which is not counted as material
| Field | 9190 | Profi Trac 2000 VL | Gap |
|---|---|---|---|
| Engine | |||
| Engine power, claimed claimed | 193.4 hp | 197 hp | — |
| Engine declared | K.H.D. BF6L 513 R-T | MAN D 2565 ME | differs |
| Displacement declared | 9.57 L | 9.51 L | — |
| Maximum torque declared | — | 542 lb·ft · 735 N·m | — |
| Transmission | |||
| Top speed declared | 18.6 mph · 30 km/h | 19.8 mph · 31.9 km/h | +6% Profi Trac 2000 VL |
| Clutch declared | — | Schlueter Hydromatik | — |
| Hydraulics & hitch | |||
| Hydraulic centre declared | Closed centre | — | — |
| Pump flow declared | 28.0 gpm · 105.9 L/min | 9.0 gpm · 34.0 L/min | +211% 9190 |
| Pressure declared | 3,771 psi · 260 bar | — | — |
| Rear PTO speeds declared | 1000 rpm | 1000 rpm | — |
| Weight & dimensions | |||
| Unladen weight declared | 16,601 lb · 7,530 kg | 20,944 lb · 9,500 kg | +26% Profi Trac 2000 VL |
| Wheelbase declared | 115.0 in · 2,921 mm | 112.2 in · 2,850 mm | — |
| Length declared | 200.0 in · 5,080 mm | 236.2 in · 6,000 mm | +18% Profi Trac 2000 VL |
| Width declared | 96.0 in · 2,438 mm | 96.5 in · 2,450 mm | — |
| Ground clearance declared | 22.0 in · 559 mm | 18.3 in · 465 mm | +20% 9190 |
| Turning radius, braked declared | 16.6 ft · 5.05 m | 15.1 ft · 4.60 m | +10% 9190 |
| Fuel tank declared | 367.7 qt · 348.0 L | 470.2 qt · 445 L | +28% Profi Trac 2000 VL |
Height is not in this table. It is not one measurement: the sources measure it to different points — over the cab on some machines, over the steering wheel or the exhaust on others — and the same tractor measured two ways can differ by most of a metre. It appears here only when both machines' figures carry the point they were measured to and it is the same point, which is not the case for these two. Each machine's own page prints its height as its source gives it.
AGCO-ALLIS 9190 sources
- Source: Traktorenlexikon, “AGCO-Allis 9190”
- Source: Traktorenlexikon, “Deutz-Allis 9170”
Schlüter Profi Trac 2000 VL sources
- Source: Traktorenlexikon, “Schlüter Profi Trac 2000 VL”