AGCO-ALLIS 9130 or Deutz-Fahr DX 6.50 A?
Which should you choose?
The data can’t decide this. Power at the PTO shaft cannot be compared: the 9130 has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft; the DX 6.50 A has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft.
Generated by rule set compare@4 from the figures on the side-by-side table, allowed by route “the same stated configuration”. Measured figures are compared only with measured, claimed only with claimed, at the same test condition; differences within each figure’s tolerance are not called.
What decides it, question by question?
| Question | 9130 | DX 6.50 A | Call |
|---|---|---|---|
| Which puts more power through the PTO shaft? | 100.8 kW (135.2 hp)Traktorenlexikon, “AGCO-Allis 9130” | 100.8 kW (135.2 hp)Traktorenlexikon, “Deutz-Fahr DX 6.50” | Not comparableNot comparable on power at the PTO shaft: the 9130 has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft; the DX 6.50 A has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft. |
| Which turns a litre of fuel into more work at the shaft? | — | — | No figureNo call on fuel efficiency at the shaft: no figure on record for the 9130 and the DX 6.50 A. |
| Which pulls harder at the drawbar? | — | — | No figureNo call on drawbar power: no figure on record for the 9130 and the DX 6.50 A. |
| Which pumps more oil for implements? | 90.7 L/min (24.0 gpm)Traktorenlexikon, “AGCO-Allis 9130” | 57.6 L/min (15.2 gpm)Traktorenlexikon, “Deutz-Fahr DX 6.50” | AheadThe AGCO-ALLIS 9130 has 57% more hydraulic flow (33.1 L/min / 8.7 gpm) than the Deutz-Fahr DX 6.50A (both pump flow, as stated by the source). |
| Which lifts more on the three-point hitch? | 3,271 kg (7,211 lb)Traktorenlexikon, “AGCO-Allis 9130” | 6,500 kg (14,330 lb)Traktorenlexikon, “Deutz-Fahr DX 6.50” | AheadThe Deutz-Fahr DX 6.50A has 99% more lift (3,229 kg / 7,119 lb) than the AGCO-ALLIS 9130 (both lift at the hitch ends, as stated by the source). |
| Which is heavier, for traction? | 5,579 kg (12,300 lb)Traktorenlexikon, “AGCO-Allis 9130” | 5,480 kg (12,081 lb)Traktorenlexikon, “Deutz-Fahr DX 6.50” | EvenEven on weight (both unladen weight, as stated by the source): the difference is under the 10% threshold, too small to call. |
| Which may carry more ballast and load? | — | 8,000 kg (17,637 lb)Traktorenlexikon, “Deutz-Fahr DX 6.50” | No figureNo call on maximum permissible mass: no figure on record for the 9130. |
| Which has the wider choice of gears? | 18Traktorenlexikon, “AGCO-Allis 9130” | 15 to 18Traktorenlexikon, “Deutz-Fahr DX 6.50” | EvenEven on forward gears (both forward gears, as stated by the source): the figures vary by configuration and the ranges overlap. |
| Which offers a creeper range? | — | — | No figureNo call on a creeper range: not stated for the 9130 and the DX 6.50 A. |
| Which is faster on the road? | 30 km/h (18.6 mph)Traktorenlexikon, “AGCO-Allis 9130” | 30 km/h (18.6 mph) to 40 km/h (24.9 mph)Traktorenlexikon, “Deutz-Fahr DX 6.50” | EvenEven on top speed (both top speed forward, as stated by the source): the figures vary by configuration and the ranges overlap. |
| Which offers more PTO speeds? | 540/1000 rpmTraktorenlexikon, “AGCO-Allis 9130” | 540/1000 rpmTraktorenlexikon, “Deutz-Fahr DX 6.50” | EvenEven on PTO speeds: the same speeds (540, 1000 rpm). |
| Which PTO runs independently of the ground drive? | independentTraktorenlexikon, “AGCO-Allis 9130” | independentTraktorenlexikon, “Deutz-Fahr DX 6.50” | EvenEven on PTO independence: every PTO is independent. |
| Which drives on both axles? | Two-wheel or four-wheel driveTraktorenlexikon, “AGCO-Allis 9130” | Two-wheel or four-wheel driveTraktorenlexikon, “Deutz-Fahr DX 6.50” | EvenEven on drive: every machine is available with four-wheel drive. |
| Which is newer, and what about parts? | 1991–1992 | 1983–1990 | Ahead (a fact, not an advantage)The AGCO-ALLIS 9130 is newer: production began 8 years later. We hold no parts-availability data, so there is no call on parts. |
What does this mean in plain words?
- The AGCO-ALLIS 9130 has 57% more hydraulic flow (33.1 L/min / 8.7 gpm) than the Deutz-Fahr DX 6.50A (both pump flow, as stated by the source).
- The Deutz-Fahr DX 6.50A has 99% more lift (3,229 kg / 7,119 lb) than the AGCO-ALLIS 9130 (both lift at the hitch ends, as stated by the source).
- The AGCO-ALLIS 9130 is newer: production began 8 years later. We hold no parts-availability data, so there is no call on parts.
- Even on weight (both unladen weight, as stated by the source): the difference is under the 10% threshold, too small to call.
- Even on forward gears (both forward gears, as stated by the source): the figures vary by configuration and the ranges overlap.
- Even on top speed (both top speed forward, as stated by the source): the figures vary by configuration and the ranges overlap.
- Even on PTO speeds: the same speeds (540, 1000 rpm).
- Even on PTO independence: every PTO is independent.
- Even on drive: every machine is available with four-wheel drive.
- Not comparable on power at the PTO shaft: the 9130 has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft; the DX 6.50 A has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft.
- No figure on record for every machine, so no call on: fuel efficiency at the shaft, drawbar power, maximum permissible mass and a creeper range.
← Every figure for both machines, side by side, with sources