AGCO-ALLIS 7600 or Deutz-Fahr Agrotron 6.00?

Which should you choose?

The data can’t decide this. Power at the PTO shaft cannot be compared: the 7600 has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft; the Agrotron 6.00 has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft.

  • The Deutz-Fahr Agrotron 6.00 suits loader and hydraulic implement work better on this data: 29% (18.3 L/min / 4.8 gpm) more hydraulic flow.
  • The Deutz-Fahr Agrotron 6.00 suits road haulage better on this data: 63% (3,300 kg / 7,275 lb) more maximum permissible mass.

Generated by rule set compare@4 from the figures on the side-by-side table, allowed by route “the same stated configuration”. Measured figures are compared only with measured, claimed only with claimed, at the same test condition; differences within each figure’s tolerance are not called.

What decides it, question by question?

Buyer questions for AGCO-ALLIS 7600 and Deutz-Fahr Agrotron 6.00, with the call on each
Question7600Agrotron 6.00Call
Which puts more power through the PTO shaft?71.3 kW (95.6 hp)Traktorenlexikon, “AGCO-Allis 7600”70.8 kW (94.9 hp)Traktorenlexikon, “Deutz-Fahr Agrotron 6.00”Not comparableNot comparable on power at the PTO shaft: the 7600 has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft; the Agrotron 6.00 has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft.
Which turns a litre of fuel into more work at the shaft?No figureNo call on fuel efficiency at the shaft: no figure on record for the 7600 and the Agrotron 6.00.
Which pulls harder at the drawbar?No figureNo call on drawbar power: no figure on record for the 7600 and the Agrotron 6.00.
Which pumps more oil for implements?64.0 L/min (16.9 gpm)Traktorenlexikon, “AGCO-Allis 7600”82.3 L/min (21.7 gpm)Traktorenlexikon, “Deutz-Fahr Agrotron 6.00”AheadThe Deutz-Fahr Agrotron 6.00 has 29% more hydraulic flow (18.3 L/min / 4.8 gpm) than the AGCO-ALLIS 7600 (both pump flow, as stated by the source).
Which lifts more on the three-point hitch?4,600 kg (10,141 lb)Traktorenlexikon, “AGCO-Allis 7600”No figureNo call on three-point lift: no figure on record for the Agrotron 6.00.
Which is heavier, for traction?3,900 kg (8,598 lb)Traktorenlexikon, “AGCO-Allis 7600”5,010 kg (11,045 lb)Traktorenlexikon, “Deutz-Fahr Agrotron 6.00”Ahead (a fact, not an advantage)The Deutz-Fahr Agrotron 6.00 is 28% heavier (1,110 kg / 2,447 lb) than the AGCO-ALLIS 7600 (both unladen weight, as stated by the source).
Which may carry more ballast and load?5,200 kg (11,464 lb)Traktorenlexikon, “AGCO-Allis 7600”8,500 kg (18,739 lb)Traktorenlexikon, “Deutz-Fahr Agrotron 6.00”AheadThe Deutz-Fahr Agrotron 6.00 has 63% higher maximum permissible mass (3,300 kg / 7,275 lb) than the AGCO-ALLIS 7600 (both maximum permissible mass, as stated by the source).
Which has the wider choice of gears?24Traktorenlexikon, “AGCO-Allis 7600”15 to 18Traktorenlexikon, “Deutz-Fahr Agrotron 6.00”AheadThe AGCO-ALLIS 7600 has 33% more forward gears (6 gears) than the Deutz-Fahr Agrotron 6.00 (both forward gears, as stated by the source).
Which offers a creeper range?YesTraktorenlexikon, “AGCO-Allis 7600”No figureNo call on a creeper range: not stated for the Agrotron 6.00.
Which is faster on the road?30 km/h (18.6 mph)Traktorenlexikon, “AGCO-Allis 7600”30 km/h (18.6 mph) to 50 km/h (31.1 mph)Traktorenlexikon, “Deutz-Fahr Agrotron 6.00”EvenEven on top speed (both top speed forward, as stated by the source): the figures vary by configuration and the ranges overlap.
Which offers more PTO speeds?540/1000 rpmTraktorenlexikon, “AGCO-Allis 7600”540/1000 rpmTraktorenlexikon, “Deutz-Fahr Agrotron 6.00”EvenEven on PTO speeds: the same speeds (540, 1000 rpm).
Which PTO runs independently of the ground drive?independentTraktorenlexikon, “AGCO-Allis 7600”independentTraktorenlexikon, “Deutz-Fahr Agrotron 6.00”EvenEven on PTO independence: every PTO is independent.
Which drives on both axles?Two-wheel or four-wheel driveTraktorenlexikon, “AGCO-Allis 7600”4WDTraktorenlexikon, “Deutz-Fahr Agrotron 6.00”EvenEven on drive: every machine is available with four-wheel drive.
Which is newer, and what about parts?1991–19961995–1997EvenSame era: production began within 5 years of each other. We hold no parts-availability data, so there is no call on parts.

What does this mean in plain words?

  • The Deutz-Fahr Agrotron 6.00 has 29% more hydraulic flow (18.3 L/min / 4.8 gpm) than the AGCO-ALLIS 7600 (both pump flow, as stated by the source).
  • The Deutz-Fahr Agrotron 6.00 is 28% heavier (1,110 kg / 2,447 lb) than the AGCO-ALLIS 7600 (both unladen weight, as stated by the source).
  • The Deutz-Fahr Agrotron 6.00 has 63% higher maximum permissible mass (3,300 kg / 7,275 lb) than the AGCO-ALLIS 7600 (both maximum permissible mass, as stated by the source).
  • The AGCO-ALLIS 7600 has 33% more forward gears (6 gears) than the Deutz-Fahr Agrotron 6.00 (both forward gears, as stated by the source).
  • Even on top speed (both top speed forward, as stated by the source): the figures vary by configuration and the ranges overlap.
  • Even on PTO speeds: the same speeds (540, 1000 rpm).
  • Even on PTO independence: every PTO is independent.
  • Even on drive: every machine is available with four-wheel drive.
  • Same era: production began within 5 years of each other. We hold no parts-availability data, so there is no call on parts.
  • Not comparable on power at the PTO shaft: the 7600 has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft; the Agrotron 6.00 has only engine power (gross or net not stated), claimed — a different quantity from power at the shaft.
  • No figure on record for every machine, so no call on: fuel efficiency at the shaft, drawbar power, three-point lift and a creeper range.

← Every figure for both machines, side by side, with sources