10 material differences · fewer than 12
Tractor oneAGCO-ALLIS 56501994–1999No measured PTO figureTractor twoLandini 5860 (DT) TL 38 N/M (TL-38 DT/M)1988–2000No measured PTO figure
Which should you choose?
Read our verdict on the 5650 and the 5860 (DT) TL 38 N/M (TL-38 DT/M) → It is generated from the rows below by a fixed, versioned rule set, and names the figure behind every call.
Field by field
10 material differences · 5 fields identical or within 5%, which is not counted as material
| Field | 5650 | 5860 (DT) TL 38 N/M (TL-38 DT/M) | Gap |
|---|---|---|---|
| Engine | |||
| Engine power, claimed claimed | 47.3 hp | 47.3 hp | — |
| Engine declared | S.L.H. 1000.3 A | Perkins D 3152 | differs |
| Displacement declared | 3.00 L | 2.50 L | +20% 5650 |
| Maximum torque declared | 123 lb·ft · 167 N·m | 130 lb·ft · 176 N·m | +5% 5860 (DT) TL 38 N/M (TL-38 DT/M) |
| Transmission | |||
| Top speed declared | 18.6 mph · 30 km/h | 18.6 mph · 30 km/h | — |
| Clutch declared | Dry SAME double clutch | Dry and air-cooled OMG double clutch | differs |
| Hydraulics & hitch | |||
| Hydraulic centre declared | Open centre | — | — |
| Pump flow declared | 8.7 gpm · 33.0 L/min | — | — |
| Pressure declared | 1,305 psi · 90 bar | 2,756 psi · 190 bar | +111% 5860 (DT) TL 38 N/M (TL-38 DT/M) |
| Rear PTO speeds declared | 540/1000 rpm | 540 rpm / 1000 rpm | differs |
| Weight & dimensions | |||
| Unladen weight declared | 4,530 lb · 2,055 kg | 4,674 lb · 2,120 kg | — |
| Wheelbase declared | 77.8 in · 1,976 mm | 77.0 in · 1,955 mm | — |
| Length declared | 133.0 in · 3,378 mm | 135.8 in · 3,450 mm | — |
| Width declared | 66.7–82.5 in · 1,694–2,096 mm | 64.2 in · 1,630 mm | differs |
| Ground clearance declared | 19.7 in · 500 mm | 15.4 in · 390 mm | +28% 5650 |
| Turning radius, braked declared | 8.9 ft · 2.70 m | 11.4 ft · 3.46 m | +28% 5860 (DT) TL 38 N/M (TL-38 DT/M) |
| Fuel tank declared | 60.2 qt · 57.0 L | 65.5 qt · 62.0 L | +9% 5860 (DT) TL 38 N/M (TL-38 DT/M) |
Height is not in this table. It is not one measurement: the sources measure it to different points — over the cab on some machines, over the steering wheel or the exhaust on others — and the same tractor measured two ways can differ by most of a metre. It appears here only when both machines' figures carry the point they were measured to and it is the same point, which is not the case for these two. Each machine's own page prints its height as its source gives it.
AGCO-ALLIS 5650 sources
- Source: Traktorenlexikon, “AGCO-Allis 5650”
Landini 5860 (DT) TL 38 N/M (TL-38 DT/M) sources
- Source: Traktorenlexikon, “Landini R 5560 L (DT)”
- Source: Traktorenlexikon, “Lindner BF 420 SN/SA”